特种定制锂电池
特种设备、卫星通讯、户外勘探、测量，便携式储能、军/警用手持装备等
特种定制锂电池
特种设备、卫星通讯、户外勘探、测量，便携式储能、军/警用手持装备等
型号编码：T300-EU/CH/UK/JP
标称电压：400WH
标称容量：25Ah
出厂电压：12.8V
执行标准：GB/T 18287-2013
工作温度：充电：0~40℃
产品规格：240*133*201
产品重量：≈2.4Kg
开发定制：OEM
产品描述：本产品是一款便携式储能产品；额定输出总功率约 400W；分别为 AC-200W//PD-45W*1/USB-24W（ USB1+USB2）/点烟器 120W ，具有交流（110VAC/200W）、USB-A、Type C、DC(5521)和点烟器 四种不同端口输出。系
| DC INPUT | ||||
| Item | Min | Type | Max | Remark |
| Rated Input voltage | 10V | 15V | 25V | Whichever Non load or loading |
| Rated Input current | - | 3A | 3.5A | |
| Rated Input power | 45W | Automatic adjustment according input power | ||
| Ripple voltage of charging | - | - | 200mV |
Test from the Input connector, oscilloscope Bandwidth setup as 20MHZ, parallel with 10uF and 0.1uF capacitor |
| Input over-current protection | - | - | - | |
| Input Lower-voltage protection | - | - | 5V | |
| Input over-voltage protection | 25V | - | 27V |
The devices will stop charging If the Input voltage exceed the protection voltage |
| Input port short-circuit protection | - | - | - | Stop charging, components no damage |
| Input polarity reverse protection | - | - | - | Support(not charging if input polarity reverse) |
| Input adapter compatibility | 10-15 VDC | |||
| Solar panel charging | 18-24V with mppt function | |||
| Pass through function | The device can support discharging while the product is charging; the Type-C Output power will drop down to 36W if the product charging via DC Input port. | |||
| LCD display of charging | Display the charging power and battery capacity | |||
| Battery charging suggestion |
|
|||
|
|
||||
| Item | Min | Type | Max | Remark |
|
PD45W Charge and Discharge |
4.75V | 5.0V | 5.5V |
20V Rated input/output current:2.25A |
| 8.55V | 9V | 9.45V | ||
| 11.4V | 12V | 12.6V | ||
| 14.25V | 15V | 15.75V | ||
| 19V | 20V | 21V | ||
|
Apple 5V/2.4A Charge and Discharge |
4.75V | 5.0V | 5.25V | Protocol: BC1.2 DCP; Apple 2.4A |
| 2.4A | ||||
| Output short circuit protection |
Turn off discharging |
|||
| Min | Type | Max | Remark | |||
| Output voltage range | 10.8V | 12.0V | 14.6V | |||
| Allowable output current | - | 10A | - | |||
| Allowable output power | - | 120W | 146W | |||
| output current | - | 10A | 12A | CV 12V test | ||
| Output ripple | - | - | < 150mV | Rated load,oscilloscope Bandwidth setup as 20MHZ, parallel with 10uF and 0.1uF capacitor, the ripple < 800mV while AC Output loading | ||
| Discharging efficiency | >92% | - | - | Test requirements: test 4 model average efficiency of 25% 50% 75% 100% of full load; test at PCBA board end. | ||
| Limited current protection | 10A | - | 13A | The output will turn off if the output current is exceed specified value; the LCD blink display AC ! while Key’s LED blinking and buzzer is ringing 3 times. The product will recover work normally after cut off the loading and press key button. | ||
| Output over-voltage protection | 15V | - | 16.8V | The output will turn off when | the product | |
| doesn't work properly and the output | ||||||
| voltage is exceed specified value. | ||||||
| Short circuit protection | - | support | - | The output will turn off and the LCD blink display AC ! while Key’s LED blinking and buzzer is ringing 3 times. The product will recover work normally after cut off the loading and press key button. | ||
| Item | Min | Type | Max | Remark | ||||
| Output voltage range | 4.75V | 5V | 5.25V | |||||
| Allowable output current | - | 2.4A | - | |||||
| Allowable output power | 12W | |||||||
| CC Output | 2.1 | 2.4 | 2.5A | CV 4.75V Test model | ||||
| Output ripple | - | - | < 150mV | Rated load,oscilloscope Bandwidth setup as 20MHZ, parallel with 10uF and 0.1uF capacitor, | ||||
| Discharging efficiency | >92% | - | - | Test requirements: test 4 model average efficiency of 25% 50% 75% 100% of full load; test at PCBA board end. | ||||
| Limited current protection | 2.5A | 3A | The output will turn off if the output current is exceed specified value; | |||||
| Output over-voltage protection | 6.2V | - | 6.8V | The output will turn off when | the product doesn't | |||
| work properly and the output voltage is exceed | ||||||||
| specified value. | ||||||||
| Short circuit protection | - |
suppor t |
- | The output will turn off if the output port is short circuit by wire or external devices; the product will be automatically recovery work normally | ||||
| after cutoff the loading. | ||||||||
| Item | Min | Type | Max | Remark |
| Item | Min | Type | Max | Remark |
| Output voltage range | 200V | 220V | 240V | |
| Rated output current | - | 0.9A | - | |
| Rated output Power | 200W | |||
| Output frequency | 47 Hz | 50 Hz | 53Hz | |
| Non-loading current | 600mA | |||
| Discharging efficiency | >85% | - | - | Test requirements: test 4 model average efficiency of 25% 50% 75% 100% of full load; test at PCBA board end. |
| Over loading protection | 220W | - | 300W |
The output will turn off if the output power is exceed specified value; the LCD blink display AC ! while Key’s LED blinking and buzzer is ringing 3 times. The product will recover work normally after cut off the loading and press key button. |
| Over temperature protection Of AC board | 80℃ | - | 100℃ | Tthe output will turn off, the product can be recovery work normally after temperature down and press the key button |
|
Over temperature recovery Of AC board |
70℃ | - | 80℃ | |
| Fan start | 55℃ | 65℃ | ||
| Fan stop | 45℃ | 55℃ | ||
| Short circuit protection | - |
suppor t |
- | The output will turn off and the LCD blink display AC ! while Key’s LED blinking and buzzer is ringing 3 times. The product will recover work normally after cut off the loading and press key button. |
Remark: the fan will stop runing if the the AC board was temperature protection.
| Item | Min | Type | Max | Remark | |
| USB1 turn-off current | - | 80 mA | 100 mA | ||
| USB2 turn-off current | - | 80 mA | 100 mA | ||
| DC turn-off current | - | 50mA | 80 mA | ||
| AC turn-off power | - | 3W | 4W | ||
| TYPE-C turn-off current | 50mA | 80mA | |||
| LED light turn-on | - | - | - | The automatic will be not available while LED light is turn on. |
Remark:
3.5 LED light function:
| LED Current | - | 150mA | 250 mA | |
| LED Voltage | - | 18V | 21V | |
| LED Power | - | 3.6W | 5.25W | |
| Lamp color temp. | - | 4500K | - | |
| Lamp qty. | 12 |
4.Battery features:
| No. | content | Testing method | Remark |
| 1 | Charge cut-off voltage | 13.8V | |
| 2 | Discharge cut-off voltage | 8.8V | |
| 3 | Standard charge |
Under the condition of the ambient temperature of 25±2℃, Charge the battery at constant current of 0.2C to reach 13.8V. Then charge the battery at constant 13.8V voltage until the charging current decreasing to 0.02C. |
|
| 4 | Standard discharge | After the standard charging,rest for 1 hour then discharge to 8.8V@0.2C. | |
| 5 | Shipments voltage | Quantity of electricity≤30 % | |
| 6 |
Maximum Charge Current |
≤12A | |
| 7 |
Maximum continuous working current |
≤30A | Instantaneous current≤ 60A time≤2S |
| 8 | Rated capacity |
Typical capacity:250000mAh Minimum capacity:24600mAh-5% |
standard discharge after standard charge |
| 9 | Operation temperature range | charge:0~40℃ | humidity:60±25% 60±25%R.H |
| discharge:-10~40℃ | |||
| 10 | Storage temperature | ≤1 month: -20 ~ 45℃ |
60±25%R.H Best 10~25℃ for |
| ≤3 months: -10 ~ 30℃ | long-time storage | ||
| ≤1 year: 0 ~ 30℃ | |||
| 11 | Impedance | <80mΩ | |
| 12 | Weight | Approx:≈2400g |
5.Environment features:
| LCD Function | Over temperature warning, display the AC ! and buzzer ringing 3 times when temperature protection action |
| Display current total charging power, discharging power. | |
| The key button’s LED blinking during abnormal of AC i protection action | |
| LED function | key button with LED |
| Discharge compatibility | The specified devices can be quick charge available. |
| Working temperature |
Charging: 0-40 °C Discharging: -10-40 °C |
| Storage temperature | -20 ~ 45℃ |
| Working Humidity | 20-90%RH |
| Storage Humidity | 10-95%RH |
6.1:ESD features:
| ESD |
|
Contact Discharge +/-4kv, Normal recovery function allowed Air Discharge +/-8kv, Normal recovery function allowed |
|
Dielectric Strength (Hi- pot) |
Inverter output L/N VS DC Input |
3000VAC 50Hz/10mA(Max)/60 Second, No breakdown and flashover |
Delivery Time:
- Material Preparation Time: 7-15 days (or inventory)
- Production & Assembly Time 3-10 days
- Testing & Packaging Time: 2-10 days
- Total Delivery Time: 30-45days
- The faster delivery could be negotiable.
Factory photo:
Contact with our sales team for your OEM and ODM order.
OEM/ODM Service:
If you want to display your own brand logo in products, bags, labels or anywhere. Or you need to develop battery packs according to your product orientation. Our OEM and ODM services are ready to do it.
Packing:
According to Stardard Export Packing.
Carton box, wooden box, wooden pallet
Ryder Electronics established in Shenzhen on July 18, 2005, mainly in the business of battery packs. In 2009 the company passed ISO9001 and improved the product quality standard to fulfill the high-end requirements from our customers.
In 2012, Ryder Electronics moved to a new facility and expend the production capacity, the Productivity improved nearly 10 times than before.
In 2013, Ryder Electronics imported ERP (SAP) system to supervise order execution process.
In 2017, Ryder Electronics expanded the SMT, imported high-speed patch machine from Germany.
Until now the factory grows into a modern enterprise which integrated injection molding, PCB designing, SMT and battery pack assembling services.
In 2018 the company passed ISO14001certification, introduced automated battery production line to further improve the production quality and capacity.
